Olivový olej servomotor poháněný čtyřmi hlavami plnění pístů ROPP kovové uzávěry uzavírající oboustranné etiketovací stroje čtvercové láhve plnicí linka plně automatická

Popis

The line specially designed for our russian customer who sent to us the glass bottles (thin&tall) is suitable for food packing industry like olive oil/wine bottles fill-cap-label process.

Samples offered by our EU customer

The whole line including filling capping labeling machine

1.model NPACK-5030 piston filling machine
2.model NPACK-AC40 ROPP capping machine
3.model NPACK-650A double sided labeling machine
4.Nitrogen gas flushing function after filling
5.Accumulation turntable for collecting final product

As below there is the basic description &introduction one by one :

►Model NPACK-5030 four heads piston filling machine

The 4heads olive filling machine,controlled by the microcomputer,combines the photoelectricity with pneumatic operation,

thus widely is applied for the liquid filling of the agriculture chemical、solution、liquid detergent、cosmetic as well as olive.The filling volume is precise,foamless and stable.

The machine can fill the liquid with the range from 25-1000ml,meanwhile there is no special requirement on the shapes of bottles.That is to say,it can fill the liquid for the normal bottles as well as the irregular-shaped bottles.

Model       NPACK-5030

Filling range     50～3000ml

Filling speed　       ＜20-30b/m（for 500-1000ml liquid）

Accuracy ±1%

Power/suppy power 0.8kw、220v

Working pressure　 5～6kg/cm3

Air consumption　  0.5-0.7mpa

N.W 500kg

Outer dimension      2000×800×1900mm

Mark:The filling nozzles can be designed and manufactured according to requirements from customers on the filling range and filling speed

Filling speed adjustment

Filling speed adjustment has the following 6 factors:

1, the speed of the product is determined by the viscosity of the product and the length of the suction pipe.

2, filling speed depends on the diameter of the filling head, the diameter is large, the speed is quick.

3, the product of the bubble level. The product filling speed of the high bubble should be slowed down.

4, how much is the filling quantity.

5, the accuracy of the filling quantity, adjust the filling time of each cast.

6, adjust the filling speed (that is, the speed of the servo motor).

General trouble shooting and processing

1）Touch screen is not shown, but the indicator light

Fault cause:

Check whether the fuse is burning, or the contact is bad, replace or reinstall the fuse.

2）The output indicator of the programmable controller has an output indicator, but the solenoid valve does not work.

Fault cause:

Upon examination of the solenoid valve failure, is the key to the programmable controller in the electrical damage, can replace the same type of intermediate relay, fault can be ruled out (this fault is very rare).
3）The main head there is a leak in the shutdown.

Fault cause:

The filling head cylinder does not move up and down, replaced PTFE head, check on the stingy joints have gas, or replace the filling valve, can be ruled out

4）After filling in a number of bottles do not fill

Fault cause:

♦Check whether the bottle counting electric eye, if not counting adjustable electric distance, so that it can reach the count;

♦ Check that the liquid level indicator is black, if it is white, and the liquid level is fluid, and can be filled with black

♦ Check the magnetic switch cylinder after the dive, the light is bright, if not bright, adjust to the light.

♦Check the back of the servo motor is close to the switch is bright, if not bright, adjust to the light.

5)Individual valve or cylinder action to slow down or do not work.

Fault cause:

♦The general situation is caused by the fault of the control valve, first check to control the output of the output of the display lamp (in the lower left of the programmable controller) work is normal, confirm the normal operation of the following check.

♦Magnet coil plug for transposition of the solenoid valve, if change the position of the fault, indicating that the electromagnet coil is damaged, replace the coil after failure can be ruled out.

If the valve group of the emptying port does not stop to have a lot of gas, the system has a more serious leakage. Can check the internal sealing condition, if damaged, should be replaced. If the fault can not be ruled out, can check the valve spool movement, see if there is a card phenomenon or the seal is damaged, and repair, if damaged more serious, it should be replaced by the entire valve.

6）Servo motor alarm.

Fault cause:

♦Check whether the PLC on the F**, if it is to turn off the power, and then open up to manual operation, a number of seconds after the manual injection, and then press the manual back to zero.

►Nitrogen gas flushing system

NPACK-AC40 Automatic ROPP capping machine for olive bottle with metal caps with protective chamber

automatický uzavírací stroj ROPP s ovládacím tlačítkem

Zakrývací hlavy pro čepičku ROPP

Uzavírací stroj je vhodným zařízením pro utěsnění hliníkových uzávěrů pro plastové láhve 、 láhve pro domácí mazlíčky glass i pro skleněné láhve pomocí válcového lisu. Před válcovým lisem z varných desek předchází šroubovací uzávěry pro lahve, automaticky plnící láhev 、 Uzávěry, odstranění zpětných uzávěrů. Uzavřená láhev upřednostňuje vlastnosti, jako je stabilní uzavírací účinek, pohodlné rozepření, takže funguje jako padělek a ochrana proti krádeži

Model NPACK-AC40

Zásobní prášek (V / Hz) AC 220/50 380/60

Kapacita (m / min) - 4000 B / M

Velikost víčka (mm) 250 - 1000

Aplikace Alum-caps

Výfuk vzduchu z vakuového pumpy (m3 / h) 5KG

Vnější rozměr （L × W × H） (mm) 2000 × 1000 × 2300

NG (kg) 520

Kreslení pracovního postupu ROPP (např. Jako automatická linka s dopravníkovou platformou)

How to operate model NPACK-C25 Single head ROPP capping machine

Podávací nádoba pohybující se na dopravním pásu se přivádí do přiváděcího hvězdného kola pomocí zaváděcího šneku, přičemž hvězdicové kolo přivádí nádobu pod těsnící hlavu v následující indexovací části, což znamená, že při vyzvednutí láhve víčko z přiváděcího žlabu plnění uzávěru miska, kde tělo a hrdlo nádoby jsou umístěny pod rotující hlavou, kde těsnicí hlava provádí dokonalou operaci závitování a těsnění.

Hlavní rysy:

Jednotka je vyrobena kompaktní a všestranná.
Dopravník SS Slat
SS Elegant Matt Finished Body
Vestavěný přední ovládací panel
Vibrační mísa
S frekvenčním měničem A / c

►model NPACK-650A double sided labeling machine

The labeling equipment is for the round bottle labeling in the industry like food、oil、pharma、wine、cosmetics and so on.

The machine with elegant design can be easily operated and maintained by the common worker,

who requires no special training in operation this machine.Just give a simple adjustment to produce another product when you want to swap the different kinds bottle labeling.

Metal caps capping+labeling line

The bottle labeler is thus out from as below-mentioned characteristics:

1:The main body of equipment is made of SUS304 and advanced Aluminum products.

2:The labeling heads is driven by the stepping motor that is imported from Japan.

3:All the light sensor equipment is imported from both Japan and Germany

4:PLC Controlled by the human-machine interface with 60 memory units

5:The machine is the best choice for single worker’s operating.

6:The machine has the function as bottle-uprighting,bottle-distributing、labeling、flating as well as counting.

7:The position、height、angle of labeling can be adjusted easily.

8:Equipped with the conveyor belt,the machine is applied to set of the production line.

Basic parameter of double sides labeling machine

turntable for accumulation of final product